-
Recent Posts
Recent Comments
- littletractorguy on Got the rototiller all mounted up on Wally
- Bill Collins on Got the rototiller all mounted up on Wally
- littletractorguy on An update on Ernie…
- Tim Boyd on An update on Ernie…
- littletractorguy on All My Deeres are finally home!
Archives
- May 2019
- May 2018
- October 2017
- May 2017
- June 2015
- April 2015
- October 2014
- July 2014
- May 2014
- April 2014
- March 2014
- February 2014
- January 2014
- November 2013
- October 2013
- September 2013
- August 2013
- July 2013
- June 2013
- May 2013
- April 2013
- March 2013
- October 2012
- September 2012
- August 2012
- July 2012
- June 2012
- May 2012
- April 2012
- March 2012
- February 2012
- January 2012
- December 2011
- November 2011
- October 2011
- September 2011
- August 2011
- July 2011
- June 2011
- May 2011
Categories
Meta
Blogroll
Category Archives: Bror
“Found” these in my stuff downstairs
“Found” these while cleaning and sorting down here…. Well actually, kidlet #2 was rummaging through my collectibles shelf…. These came from my grandfather. More update pics to follow, tonight…
Posted in Bror
Leave a comment
Cool old JD attachment!
So I was going through the pile of tractor documents for my grandfather’s 112H yesterday when a little folded up piece of paper fell out of one of them… When I unfolded it, this is what I found: Its a … Continue reading
Finally got time to get out to the garage on the 14th, (Jbefore the weather turned cold on us). Cleaned up enough that I was able to get the transaxle onto my little engine stand. Had to put another brace … Continue reading
Bearing removal and installation thoughts!
So, I got a bunch of advice about what to do about the bearings on those axle housings, and the consensus is I should replace them. Then of course, the question is, how the heck do I get them OUT … Continue reading
Posted in Bror, Tools, Tractor Repair Stuff
Tagged Axle Housing, Bearing Puller, Bror, John Deere 112, restoration, Tap and Die set, transaxle
Leave a comment
More Transaxle adventures!
Got back out for a bit to work on the transaxle tonight… Pulled off the drive sheave and the hub that sat behind it So that I could get in behind to clean. So here’s the main input shaft… Then … Continue reading
Started cleaning up the transaxle tonight!
So I went after the transaxle for a bit tonight out in the garage, thanks to Kidlet #2 being handy to keep an ear out for LTBabe…. The hitch plate and rear support for the tractor is bolted onto the … Continue reading
Whoo hoo! Got the transaxle out!
Went out to take a few measurements off Ernie, then thought, what the heck, I’d try pulling that clevis out, after it sat for a week soaked in WD-40… Bad news is, my ATV jacks safety stops must have slipped, … Continue reading
Posted in Bror
Tagged Brake Clevis, Bror, John Deere, John Deere 112, restoration, transaxle
Leave a comment
Transaxle part way!
Since I got so carried away with trying to get the transaxle out, I DIDN’T take the time to take a pic of it partway out for future reference. Here it is, being held up by my ATV jack. I … Continue reading
Well, SOME progress on the transaxle, but….
So, I got Bror jacked and set down on the jack stands Got the idler spring disconnected, Took off the rims disconnected what I THOUGHT was the brake clevis, Then I pulled all the bolts. For reference, there’s the three … Continue reading
My next steps with Bror
So, Team Green, one of the other MTF members, asked me last night in the MTF chat room what my next steps will be for Bror… Well, I KNOW the engine runs… But its too cold now here to actually LINE … Continue reading